All articles
concealed-hingesfunctional-hardwarehingesinhouse

110 Degree vs 170 Degree Cabinet Hinges: Most Doors Never Need the Extra Swing

A 110-degree concealed hinge suits nearly every ordinary door. Wide-angle hinges belong in front of pull-outs and in corners, and they bring bulk with them.

For a standard kitchen, put 110 degree hinges on the ordinary doors and buy 170 degree cabinet hinges only for the few doors that hide pull-outs, inner drawers or a corner. The 110 vs 170 question is really a question about what sits behind each door. An empty box with shelves gains nothing from the extra swing, while a door covering a rollout shelf can block it unless the hinge gets the door fully out of the opening. One thing changes that advice: if the cabinet holds internal drawers, check the hinge for zero protrusion, not just a big opening angle, because the angle alone does not promise the drawer will clear.

What the degree on the box actually measures

The number is the opening angle: how far the door can swing, counted from closed at zero. A door on a 90 degree hinge would stop exactly square to the cabinet. At 110 degrees it travels a little past square, enough to stand out of the way of a hand and an armful of plates. At 170 degrees the door folds back until it nearly lies against the cabinet beside it, ten degrees short of flat.

Concealed hinges are generally sold in three loose bands. Opening angles of roughly 105 to 120 degrees form the everyday range, and within it the hinges are close to interchangeable in use; 105, 107, 110 and 120 are all common labels. Below that sit hinges near 95 degrees, used for thick doors and some specialty cases. Above it are the wide-angle hinges, typically 155, 165 or 170 degrees, built for doors that have to get completely clear of the opening.

Opening angle Where it earns its place What it costs you
About 95 degrees Thick doors that would bind on a standard hinge; some blind corner setups The door barely passes square
105 to 120 degrees Ordinary doors over shelves, sinks and open boxes The door edge still sits partly in the opening
155 to 170 degrees Doors over pull-outs and inner drawers; corner and bifold doors A bulkier hinge, more hardware inside the box, and a door that can swing into its neighbor

Why 110 is my default for a standard kitchen

Watch how a cabinet door gets used. You open it, reach in, take something out and let it close. An upper door rarely needs pushing to its limit with a mug in one hand, and a 110 degree door is already beyond square, out of the path of a shoulder. On a cabinet with fixed shelves, nothing inside asks for more.

The everyday hinges are also the plain ones. Wide-angle hinges are physically larger, with a heavier arm and a more involved linkage, so they take up more room inside the cabinet when the door is shut. They generally cost more per hinge too, and a kitchen holds a lot of hinges. Putting 170s on every door would buy bulk and expense in places that never use the extra travel.

The tradeoff of my pick is the one wide-angle hinges exist to solve. With a standard hinge, the open door does not get entirely out of the cabinet opening; its edge and back still occupy a sliver at the hinge side. That costs nothing in front of shelves. In front of anything that slides out, it is where trouble starts.

Doors that hide something that slides out

Rollout shelves, pull-out trash bins, inner drawers behind a pair of doors and tall pantry pull-outs all travel straight forward on drawer slides. If the door is still hanging in the opening, the front of the pull-out meets the back of the door, scuffs it, or simply stops. This is where I would put the wide-angle hinges: they carry the door far enough around to stand clear of the opening, so the pull-out has its full width to come forward.

Here is the detail most comparisons skip. Opening angle and protrusion are separate measurements. Some hinges are sold as zero protrusion, meaning the hinge geometry moves the door completely out of the opening when it is open, and one major hinge maker sells its zero-protrusion model at 155 degrees, specifically for cabinets with inner pull-outs. A 170 degree hinge swings farther, but its spec sheet may or may not claim zero protrusion. If the cabinet holds internal drawers, read the hinge's protrusion spec for your exact door overlay and frame type before you order, and treat the angle as the second number, not the first.

Even then, the pull-out only clears if the door is actually opened. A door that a busy person swings to square and no farther can still be in the way of a full-width drawer, which is why some cabinet builders also space the slides inward from the frame. If the cabinets are not built yet, ask whoever is building them how the pull-outs will clear the doors.

Corners and bifolds, briefly

Wide-angle hinges also show up in corner cabinets, where a door has to fold well back to open up an awkward space, and on bifold corner doors, where one door folds against its partner. Corner cabinets bring their own hinge types as well, so a corner deserves its own planning rather than a blanket rule; our corner hinge piece covers that ground. In a straight run of base and wall cabinets, the corner is usually the only place a 170 earns its keep without a pull-out behind it.

Where the wide swing gets in the way

A door that swings to 170 degrees goes wherever 170 degrees takes it. Next to a wall, a tall pantry, a refrigerator side or the handle of a built-in appliance, that means the door edge, and any knob or pull on it, can strike whatever stands beside it. Two wide-angle doors that open toward each other across an inside corner can also meet. On a standard hinge the same door would have stopped short.

When a door is too generous, an angle restrictor is the fix. Several concealed hinge systems accept a small clip-on stop that limits the opening: one large maker offers a stop that holds its 110 degree hinge to 86 degrees, and stops for its 155 degree hinge at 92 or 110 degrees, sold for doors that would otherwise hit walls, protruding cabinets or a neighboring appliance handle. These stops are specific to a hinge series, so match the stop to the hinge part number. I like the alternative just as much: choosing a lower-angle hinge from the start for a door you already know is tight.

Bulk is the other nuisance. A wide-angle hinge occupies more of the cabinet interior near the hinge side, which can matter on a narrow cabinet or one with a pull-out sized close to the opening. Check the clearance the hinge maker lists against what is going inside the box.

Open your doors once before ordering a single hinge

The most useful check costs nothing. Walk your existing kitchen, or the cabinet drawings, and for each door ask three questions.

  • What is behind it? Shelves or an open box: standard angle. Anything on slides: wide angle, with zero protrusion where the drawer runs close to the opening.
  • What is beside it? A wall, an appliance, a tall cabinet or a door opening toward it: plan a restrictor, or a lower angle, before the door chips anything.
  • How thick is it? Doors thicker than the usual 3/4 in can bind on a standard-angle hinge; look for a hinge rated for the door thickness.

Every concealed hinge is also chosen by overlay and cabinet type, face frame or frameless, and those come first; the angle is a choice made inside the hinges that already fit. Read those details first when you shop cabinet hinges, and our cabinet hinge installation guide walks through mounting them. If a corner door is part of the plan, look at the lazy susans or pull-outs going behind it before choosing its hinge.

Shop Cabinet Hinges

Browse all 83 in Cabinet Hinges → Cabinet knobs Cabinet pulls & handles

Shop the guide →