Swapping hardware on KraftMaid cabinets means matching hole spacing, door style, and finish to boxes that were likely predrilled at the factory — get any of the three wrong and you're stuck with visible extra holes. This guide breaks down what actually matters when shopping cabinet hardware for KraftMaid cabinets in 2026, with specific picks and what to skip.
- Cabinet hardware for KraftMaid cabinets works best when new hole spacing matches the existing predrilled pattern exactly.
- Schaub and Company's 704-PN Traditional Round Knob in polished nickel is the safe pick for raised-panel KraftMaid doors — Buy.
- Top Knobs' Chareau Reeded Knob in Honey Bronze suits KraftMaid's shaker lines for a 2026 transitional refresh — Buy.
- Skip oversized 8-inch bar pulls on KraftMaid's narrower door stiles; they overhang the frame and look off-balance.
- Measure before you order — a mismatched hole pattern is the single most common return reason on cabinet hardware.
Shop the picks from this guide
In stock at Knobs.co · Free shipping on hardware orders $99+ · 110% price match
-
Alno
Alno A1032 1'' Brass Cabinet KnobPolished Brass
$13.46
$14.95 -
Alno
Alno A726 Charlie's 3 1/2'' CC Cabinet PullAntique English / 3''
$24.26
$26.95 -
Alno
Alno A1298 128mm 5'' CC Brass Cabinet PullBarcelona
$19.76
$21.95 -
Alno
Alno A1033 1 1/8'' Brass Cabinet KnobPolished Brass
$18.86
$20.95 -
Alno
Alno A960 Tab 1 1/2'' CC Brass Cabinet PullBronze / 3/4''
$16.16
$17.95 -
Alno
Alno A1145 1 1/4'' Brass Cabinet KnobBarcelona
$17.96
$19.95
Why this matters
KraftMaid cabinets ship in framed and shaker-style configurations across dozens of door profiles, and most of them arrive predrilled for a specific hole pattern chosen at time of order. Order the wrong knob or pull and you're either drilling new holes into a factory door face or living with two sets of holes forever. That's the whole ballgame with cabinet hardware for KraftMaid cabinets — it's a measurement problem before it's a style problem.
Before you pick a finish, measure your existing pull hole spacing center-to-center. Most stock cabinet lines, KraftMaid included, land on one of a handful of standard spacings, and matching that number narrows your hardware search fast.
Who this is for
This guide is for homeowners updating an existing KraftMaid kitchen or bath — not building new cabinets from scratch. If you're refinishing shaker or raised-panel KraftMaid doors and want new knobs or pulls without redrilling every door and drawer front, the criteria below apply directly to you. Contractors and designers managing multiple KraftMaid installs will find the spacing and finish notes useful for bulk ordering too.
What to look for in cabinet hardware for KraftMaid cabinets
Hole spacing that matches your existing pattern
This is the single most important variable. KraftMaid cabinet lines typically use one of three common pull spacings — 3 inches, 3-3/4 inches, or 5 inches center-to-center — and knobs are single-hole regardless of collection. Measure the existing screws before ordering anything; a pull with the wrong spacing means new holes, period.
Door style compatibility
KraftMaid's door styles run from flat-panel shaker to raised-panel traditional to slab-front contemporary, and hardware should scale with the door's visual weight. A heavy, ornate knob looks out of place on a flat shaker door; a minimal bar pull can look thin against a deep raised panel.
Finish match to existing fixtures
Most kitchens already have a faucet, cabinet pulls on an island, or bath fixtures in a set finish. Matching or intentionally contrasting that finish — polished nickel, honey bronze, matte black — keeps the room from looking like two separate renovations happened five years apart.
Base material and grip durability
Zinc-alloy knobs are lighter and cheaper but can develop play in the mounting screw over a few years of daily use. Solid brass and stainless bases hold their finish and grip longer, which matters more on high-traffic doors like the sink base or trash pull-out.
Screw length for door thickness
Most framed cabinet doors, KraftMaid's included, run close to 3/4-inch thick, and the standard 1-inch mounting screw included with most knobs and pulls clears that with room to spare. If your doors are thicker (built-up shaker panels, some inset styles), confirm screw length before checkout so you're not stuck with a knob that won't seat flush.
Top picks for KraftMaid cabinets
The safe pick: Schaub and Company 704-PN Traditional Round Knob
The Schaub and Company Traditional Round Knob, 1-1/2 inches in diameter and finished in polished nickel, is built for KraftMaid's raised-panel and traditional door lines. It's a single-hole mount, so hole spacing isn't a variable — only placement. Polished nickel reads clean against both white and stained wood KraftMaid finishes, and the round profile is proportional to a deeper panel door. Verdict: Buy for anyone with traditional or transitional KraftMaid cabinetry.
The transitional pick: Top Knobs TK320HB Chareau Reeded Knob
The Top Knobs Chareau Reeded Knob in Honey Bronze brings a fluted, textured face that photographs well on KraftMaid's flat-panel shaker doors — the reeding adds visual interest a plain knob can't. Honey Bronze sits warmer than brushed nickel, which pairs naturally with the warm wood tones common in KraftMaid's stained maple and cherry lines. It's a compact, single-hole knob, so it drops straight into an existing bore. Verdict: Buy if your kitchen is leaning warm-toned for 2026.
The value pick: Amerock BP36838 Status Pull
The Amerock Status pull is a straightforward bar-style pull sized for standard drawer fronts, and Amerock's Status line is priced to make a full-kitchen swap affordable without cutting corners on finish quality. It's a practical choice for anyone replacing hardware across 20-plus drawers and doors where budget scales fast. Verdict: Consider — it's the right call on volume jobs, less so if you want a single showpiece pull on an island.
What to avoid
- Oversized 8-inch-plus bar pulls on standard KraftMaid door stiles. They look proportional in photos but overhang narrow face frames in person, especially on upper cabinets.
- Hollow zinc knobs with no weight to them. They mount fine on day one and develop wobble within a year or two of daily grip.
- A finish that ignores your faucet and lighting. Matching cabinet hardware to fixtures already in the room reads intentional; picking a finish in isolation reads accidental.
“If the screw holes don't line up, no finish will save the look.”
Verdict comparison
| Pick | Style Fit | Base Material | Mount | Verdict |
|---|---|---|---|---|
| Schaub 704-PN Traditional Knob | Raised panel, traditional | Solid metal, polished nickel | Single-hole | Buy |
| Top Knobs Chareau Reeded Knob | Shaker, transitional | Solid metal, Honey Bronze | Single-hole | Buy |
| Amerock Status Pull | Shaker, contemporary | Zinc alloy | Two-hole | Consider |
FAQ
What cabinet hardware fits KraftMaid cabinets?
Any knob or pull that matches your existing hole spacing and door thickness fits KraftMaid cabinets — there's no proprietary mount. Measure center-to-center spacing on pulls and confirm door thickness before ordering in 2026.
Is KraftMaid hardware different from standard cabinet knobs?
No, KraftMaid uses standard single-hole knob mounts and standard two-hole pull spacing like most framed cabinet brands. The only variable is which specific spacing was predrilled at the factory for your order.
What size knobs work best on KraftMaid shaker doors?
A 1 to 1-1/2 inch round or reeded knob proportions well against KraftMaid's flat shaker panels. Anything larger tends to visually crowd the narrower stile on shaker-style doors.
How do I measure existing KraftMaid pull spacing?
Measure center-to-center between the two mounting screws on an existing pull, not the outer edges of the hardware itself. Most land on 3 inch, 3-3/4 inch, or 5 inch spacing.
Can I replace KraftMaid knobs without redrilling?
Yes, since knobs use a single mounting hole, any new knob drops into the existing bore regardless of brand. Pulls require matching the exact hole spacing to avoid redrilling.
What finish matches KraftMaid's stock hardware?
There's no single stock finish across KraftMaid lines, so match new hardware to your faucet, lighting, or appliance finish instead. Polished nickel and honey bronze both read well against KraftMaid's common wood tones.
How much does it cost to swap cabinet hardware in 2026?
Cost scales with piece count and material — a full kitchen typically runs anywhere from a modest budget swap using zinc alloy pulls to a higher spend on solid brass across 20 to 40 pieces. Check current per-piece pricing before totaling a full kitchen.
What's the best pull length for KraftMaid drawers?
Pull length should scale with drawer width — a 5-inch pull suits standard drawers while wider drawers over 24 inches look better with a longer bar pull. Center the spacing on the drawer face rather than defaulting to factory placement.
One last thing
The most common mistake on a KraftMaid hardware swap isn't finish or style — it's ordering knobs for doors and pulls for drawers without checking that a few doors in the kitchen were actually predrilled for pulls, not knobs. Builders sometimes mix mount types across a single kitchen order. Count your actual hole patterns door by door before you place a bulk order, not after.
