24 inch (609.6 mm) drill-center pulls for refrigerator panels and full-height doors
24 inch (609.6 mm) drill-center pulls are large appliance pulls used on full-height refrigerator panels, freezer columns, integrated wine storage, and oversized pantry doors. The 609.6 mm spacing pairs with panel cabinetry between 24 and 36 inches wide. A long single pull at this length defines the door face from top to middle or middle to bottom. The size is one of the most-shopped specs within the full-height appliance pull range.
Where 24 inch fits
Column refrigeration with full-height doors, particularly Sub-Zero, Thermador, Gaggenau, and Miele integrated columns. Tall pantry runs in custom kitchens. Some commercial-style residential refrigeration brands also spec this length on their panel-ready models. The pull is long enough to function as the primary visual line of the cabinet face. Some projects also use 24 inch on stacked appliance pairs where both upper and lower units take the same long pull.
Style range at this size
Heavy solid-bar pulls and architectural T-pulls. Squared, round, and flat-strap profiles. Construction at this length is engineered specifically for appliance loads, with reinforced mounting points and through-bolt fastener systems. Lighter-weight tubular pulls aren't viable at 24 inch because of the lever-arm forces on the mounting hardware. The finish catalog leans modern: brushed stainless, matte black, satin nickel, and aged bronze carry the broadest selection.
Adjacent sizes worth comparing
For narrower fronts, see 18 inch (457.2 mm). For wider, step up to 30 inch (762 mm). For the dedicated category, see appliance pulls. Replacement-shopping at this size on existing Sub-Zero or Gaggenau column installations should default to the appliance manufacturer's documented pull spec rather than a tape measurement, since the panel pull screws can sit recessed.
Frequently Asked Questions
How do I measure whether my existing refrigerator panel takes a 24-inch drill-center pull?
Measure center-to-center between the two existing screw holes on the panel door — if that distance is 24 inches (609.6 mm), the pull is a direct replacement. Do not measure the overall pull length, which includes the overhang beyond each mounting point. On integrated columns from Sub-Zero, Thermador, Gaggenau, or Miele, cross-check the measurement against the appliance manufacturer's documented pull spec, since mounting screws can sit recessed and a tape reading may read slightly short.
What door or panel widths are a practical match for a 24-inch (609.6 mm) drill-center pull?
The 609.6 mm drill-center spacing is suited to panel cabinetry between 24 and 36 inches wide, which covers standard full-height refrigerator column panels. At 24-inch panel width the pull spans most of the door face and serves as the primary visual line; on a 36-inch-wide front it is proportionally centered without appearing undersized. Narrower cabinet fronts below 24 inches should use a shorter drill-center spec to keep adequate edge clearance at each mounting point.
How does the 24-inch (609.6 mm) drill-center size compare to the adjacent 18-inch (457.2 mm) size, and when should each be used?
The 18-inch (457.2 mm) drill-center is the step down and suits narrower appliance fronts or tall pantry doors on cabinets less than 24 inches wide, where a 24-inch span would leave insufficient material between the mounting hole and the door edge. The 24-inch (609.6 mm) size is the standard for full-height integrated column refrigeration — it runs from the top to the midpoint of the door or midpoint to bottom, defining the full face. Projects with stacked appliance pairs that require a consistent pull line across both units typically use the 24-inch spec on both, whereas 18-inch pairs are more common on side-by-side or counter-depth configurations.
What construction and finish options are available at the 24-inch drill-center length, and why are some pull types not viable at this size?
At 609.6 mm, structural integrity is a design requirement: solid-bar, heavy T-bar, and flat-strap architectural profiles engineered with reinforced mounting points and through-bolt fastener systems are the viable options. Lightweight tubular pulls are not suitable at this length because the lever-arm forces on the hardware — generated by gripping and pulling a full-height door — exceed what thin-wall tube construction can reliably handle at the mounting joints. Finish availability at this size skews modern: brushed stainless, matte black, satin nickel, and aged bronze carry the broadest selection across manufacturers.
What Customers Say
Trusted by thousands of designers, builders, and homeowners
Kayla Malo is the most attentive and super human ever! My experience with this company is stellar!
Love working with Kayla, she is extremely helpful and quick with responding to my questions!
Kayla was GREAT!!!! Super help and fast answers. One of the best I've ever dealt with.