All articles
door-hardwareinhousepush-pull-door-hardwareswinging-door

Push Pull Door Hardware for the Swinging Door Between Kitchen and Dining Room

Push and pull plates belong on doors that open without turning anything. On a door that swings both ways, a plate on each face beats a pull.

Push pull door hardware belongs on a door that opens without anything being turned: in a house, that usually means the swinging door between the kitchen and the dining room or butler's pantry, and sometimes a one-way service door held shut by a roller latch. My recommendation for a door that swings both ways is a push plate on each face and no pull at all. If the door swings in one direction only, put a plain plate on the side you push from and a plate with a grip on the side you pull from. And if the door already has a knob or lever that has to be turned, plates are protection for the paint rather than the way the door opens, so buy them for that reason or skip them.

A plate is for a door with nothing to turn

A push plate is a flat metal panel screwed to the door where hands land. It has no moving parts and does nothing mechanical; it gives the hand a place to push and takes the wear that would otherwise land on paint or varnish. A pull plate is the same panel with a grip mounted on it, for the side of the door that has to be drawn toward you. Neither one retracts a latch. That single fact sorts every door in the house: if the door latches, the plates ride along with a lockset; if it does not, the plates are the hardware.

Doors that do not latch are rarer in houses than in restaurants and offices, which is why the advice that ranks for push and pull plates is written for commercial buildings. The residential cases are specific, and each one wants a slightly different setup.

Door How it opens What I would put on it
Kitchen-to-dining swinging door Both ways, returning to center A push plate on each face
Butler's pantry or service door that swings one way One way, held by a roller latch Push plate on the push side, plate with grip on the pull side
Half-height café doors Both ways, usually pushed with a hip or tray Small plates, or none
Any door with a knob or lever Turn, then push or pull A plate only if the paint around the handle is wearing

Why a door that swings both ways gets two push plates and no pull

On a double-acting door there is no pull side. Whoever reaches it pushes, from whichever room they are in, and the hinge brings it back to center. A pull on that door asks people to tug at something that is easier to push, and it gets in the way on the swing: when someone pushes the door open from the other room, the face carrying the pull turns toward the wall beside the doorway, and a projecting grip is the first thing to reach it. A flat plate lets the door open wide in both directions with nothing to strike. If the door does reach a wall, a door stop on that wall protects both the plaster and the plate.

The tradeoff is real. A door with only flat plates gives you nothing to hold, so you cannot ease it closed behind you or steady it while someone carries a tray through from the other side. Hinges matter here too. Gravity-type double-acting hinges are commonly sold with a hold-open position, while many spring-type ones close every time, and the hinge decides whether the door stays put while you carry a load through. The plates do not change that, so choose the hinge for the traffic and the plates for the hands.

When one face does need a grip

A service door that swings one way, say from the kitchen into a pantry, has a push side and a pull side like any ordinary door. That is where a push/pull set earns its name: plate on the push face, plate and grip on the pull face, and a roller latch in the edge to keep the door from drifting open, since neither plate holds anything shut. Rocky Mountain Hardware sells its push/pull sets in a run of functions on the same plate design, from a single push plate alone, to push plates on both faces, to push and pull with no lock, to versions that add a deadbolt keyed on one side or on both. I would read the function name on the order before anything else, because the same plate is a very different purchase depending on which one you choose. The grip itself is chosen separately from a range of Rocky Mountain profiles, and the door grips they come from are the same family used on full entry doors, so a pantry and a front door can carry the same shape at different sizes.

Size the plate to the stile, not to the door

On a paneled or glass-lite swinging door, the plate sits on the vertical stile beside the panels, and the stile's width sets the plate's width. A plate that runs edge to edge across a stile looks crammed and leaves the screws close to the joint; one that leaves a visible margin on both sides reads as fitted. On a door with a full glass lite the stiles can be narrow, and that is when the slimmer plates in a range are worth seeking out. A flat slab door has no stile to respect, so width becomes a matter of proportion and of how big a hand target you want.

Length is about the range of heights at which people push. Adults push around mid-height, children lower, and someone with full arms pushes with a forearm, a hip or a shoulder. A long plate covers more of those contact points, which is why the longer plates in a range suit a busy kitchen door, while a short plate on a quieter pantry door can sit at hand height and leave everything above and below it bare. On a kitchen door I would go long. Rocky Mountain's plates run from about a foot to nearly three feet long and from roughly two to four inches wide, so there is room to fit both the stile and the traffic.

Let the old finish show you where the plate goes

If the door has been swinging for a while, it has already recorded where people push. Look at it in raking light, with a lamp held low and off to one side: the dull, slightly darker patch on each face, sometimes with a ring of grime at its edges, is the true contact zone. Measure its top, its bottom and how far it sits from the door's free edge. Those three numbers tell you the plate's length and where to center it, and they are better information than any standard height, because they come from the people who actually use the door. Clean the door and touch up the paint before the plate goes on; a plate mounted over the worn patch will not hide a dark halo that extends past its edges.

A new door has no history, so I would center the plate where your own palm lands when you push with your arm relaxed, then have the shortest and the tallest regular user of the door try it before you drill.

Before you drill for push pull door hardware

  • Check the door's thickness. Interior doors are often 1-3/8 in thick, and some push/pull sets are drawn for 1-3/4 in doors; Rocky Mountain's Edge sets, for one, state a 1-3/4 in minimum. The door prep sheet on each product page is the document to read.
  • If you choose a deadbolt function, the door needs boring for it, and the plates are cut around the cylinder and thumbturn. Order the function and prep the door to match.
  • On a double-acting door, mount both plates at the same height so the door looks the same from both rooms.
  • Leave a margin between the plate and the door's free edge, so knuckles stay clear of the frame as the door passes it.
  • Choose the finish with both rooms in mind, since each face of a swinging door is seen from a different room.

Shop Door Hardware - Push Pull Sets

Browse all 12 in Door Hardware - Push Pull Sets → Cabinet knobs Cabinet pulls & handles

Shop the guide →