Picking the right pull for kitchen cabinets in 2026 comes down to three numbers: center-to-center spacing, finish, and how many drawers you're outfitting. This hardware resource ranks eight pulls across price points and shows you which one actually fits your kitchen instead of just looking good in a product photo.
- Top Knobs Garrison pull (7-9/16 inch cc, Honey Bronze) wins for traditional kitchens in 2026 - Buy.
- Atlas Homewares Tustin pull in stainless (6.5 inch cc) is the safest match for stainless appliances - Buy.
- Berenson Metro pull (224mm cc, Matte Black) is the modern minimalist pick - Buy.
- Jeffrey Alexander Griffin bar pull (160mm cc) costs less but ships in fewer finish options - Consider.
- Knobs.co stocks 50,000+ cabinet hardware SKUs, so matching cc spacing across a whole kitchen is realistic without redrilling.
Why This Matters
Most kitchen hardware mistakes aren't about style, they're about spacing. Buy a pull with the wrong center-to-center measurement and you're either patching old holes or drilling new ones through a painted or stained finish that shows every mistake.
Before you shop by finish, get the size right. A short pull sizing guide for kitchen islands walks through matching pull length to door and drawer width, which matters more for how a kitchen reads from across the room than finish does.
“If the pull's center-to-center doesn't match your old holes within an eighth of an inch, you're drilling new ones.”
Cabinet hardware is also one of the few remodel line items where the manufacturer sets the price, not the retailer. That's why cross-shopping the same SKU across sites rarely turns up a real discount, and why a price match policy matters more than a flash sale.
How These Pulls Were Ranked
Each pull on this list was evaluated on four things: center-to-center spacing relative to standard 3 inch, 4 inch, and 5 inch drawer bores, finish durability claims from the manufacturer, cross-brand availability in 2026 catalogs, and how the pull performs at scale across a full kitchen versus a single accent drawer. Pulls that only work as one-off statement pieces got marked down even when the design was strong. Pulls with wide cc ranges and finish families that show up across multiple brands ranked higher because they're easier to match later if a cabinet gets replaced or a new run gets added.
The Ranked List
1. Top Knobs Garrison Pull - The Traditional Pick
The Garrison pull from Top Knobs runs 7-9/16 inch center-to-center in a Honey Bronze finish. It reads as classic hardware without tipping into ornate, which is why it shows up in traditional and transitional kitchens more than any single Top Knobs pull in this size range. Buy if your cabinets are stained wood or a warm painted finish.
2. Atlas Homewares Tustin Pull - The Stainless Standout
The Tustin pull sits at 6.5 inch cc in a stainless finish that matches stainless appliance panels without the yellow undertone some "brushed nickel" finishes carry. If your kitchen has a stainless range, hood, and fridge, this pull disappears into the palette instead of fighting it. Buy.
3. Berenson Metro Pull - The Modern Minimalist
The Metro pull uses 224mm cc in Matte Black, a length that suits wide flat-front drawers on frameless European-style cabinets. Matte black at this length holds up on high-traffic kitchen islands better than smaller matte black pulls that show fingerprints faster relative to their surface area. Buy for flat-front, handle-forward kitchens.
4. Jeffrey Alexander Griffin Bar Pull - The Budget Bar Pull
The Griffin bar pull ships at 160mm cc in the DBAC finish code. It's priced for a full kitchen swap-out where you need 20-30 matching pulls and don't want the per-unit cost of a premium finish line. The tradeoff is fewer finish variants than Top Knobs or Berenson offer at the same cc. Consider if budget across a large quantity matters more than finish depth.
5. Belwith Keeler Berkshire Pull - The Two-Tone Match
The Berkshire pull runs 7-9/16 inch cc in Champagne Bronze, a finish that's been the default warm-metal choice for two-tone kitchens through 2026 remodels. It pairs a brass-adjacent tone with enough grey undertone to sit next to both white uppers and navy or green lowers. Buy for two-tone cabinet runs.
6. Elements Torino Bar Pull - The Small-Drawer Specialist
At 4 inch cc, the Torino bar pull in the MB finish code is sized for narrow drawers, spice pull-outs, and vanity drawers rather than full-width base cabinet drawers. It's a strong secondary pull in a kitchen that's already using a longer pull as the primary hardware. Consider for narrow drawers only, not as your only pull.
7. Amerock Winsome Appliance Pull - The Appliance Crossover
The Winsome appliance pull spans 12 inch cc and is built for dishwasher and panel-ready appliance fronts, not standard cabinet drawers. It shows up on this list because kitchens increasingly match appliance pulls to cabinet pull finish rather than treating them as a separate category. Consider if you're panel-fronting an appliance in the same run as your cabinets.
8. Du Verre Series 3 Large Pull - The Statement Island Pull
At 9.75 inch, the Series 3 large pull is built for wide island drawers and oversized cabinet doors where a standard 6 inch pull would look undersized. It's not a pull you buy in bulk for a whole kitchen, it's a pull you buy for the two or three drawers that need to make a statement. Buy for kitchen islands specifically.
Finish coordination matters beyond the cabinets themselves. Kitchens that pair a warm bronze or champagne pull with a busy natural-stone counter tend to look cluttered, and the same logic that governs quartz countertops for kitchens — pick the material with the least competing pattern first, then layer hardware and fixtures around it — applies just as directly to pull finish selection.
Comparison Table
| Pick | CC Spacing | Finish | Best For | Verdict |
|---|---|---|---|---|
| Top Knobs Garrison | 7-9/16 in | Honey Bronze | Traditional kitchens | Buy |
| Atlas Homewares Tustin | 6.5 in | Stainless | Stainless-appliance kitchens | Buy |
| Berenson Metro | 224 mm | Matte Black | Flat-front modern kitchens | Buy |
| Jeffrey Alexander Griffin | 160 mm | DBAC | Budget full-kitchen swaps | Consider |
| Belwith Keeler Berkshire | 7-9/16 in | Champagne Bronze | Two-tone kitchens | Buy |
| Elements Torino | 4 in | MB | Narrow/vanity drawers | Consider |
| Amerock Winsome | 12 in | Appliance-matched | Panel-ready appliances | Consider |
| Du Verre Series 3 | 9.75 in | n/a | Islands and oversized doors | Buy |
Where to Buy
Three rules keep a pull order from becoming a return:
- Order samples before you order 30 units. Finish names like Honey Bronze, Champagne Bronze, and Golden Champagne look nearly identical on a screen and different under kitchen lighting — a physical sample settles it in seconds.
- Confirm cc spacing against your existing holes, not the cabinet spec sheet. Builder-installed cabinets don't always match the drawer bore spacing the cabinet line advertises.
- Price match before you buy elsewhere. Since manufacturer pricing rarely varies retailer to retailer, a 110% price match guarantee is worth checking before assuming another site is cheaper.
Knobs.co carries all eight pulls above alongside 50,000+ other cabinet hardware SKUs, which matters if a future cabinet addition needs to match a finish you bought in 2026.
FAQ
What's the best cabinet pull size for kitchen drawers in 2026?
Most standard kitchen drawers use a 3 inch to 5 inch center-to-center pull; wider drawers and islands move up to 6.5 inch to 12 inch. Measure your existing holes first, since matching cc spacing avoids redrilling.
Is a bar pull better than a knob for kitchen cabinets?
Bar pulls are easier to grip with wet or full hands, which is why kitchens favor them over knobs on drawers. Knobs still work fine on cabinet doors where a full grip isn't needed as often.
How much center-to-center spacing do I need for a 12 inch appliance pull?
A 12 inch appliance pull needs 12 inch center-to-center mounting holes, matching the Amerock Winsome pull's spec exactly. Panel-ready dishwashers and fridges typically call for this length.
What's the best hardware resource for finding matching cabinet pulls in bulk?
A hardware resource that stocks a single finish across multiple cc lengths, like Knobs.co's 50,000+ SKU catalog, makes bulk matching realistic. Buying from a retailer with only a handful of SKUs per finish risks running out mid-project.
Do champagne bronze and honey bronze finishes look the same?
No, champagne bronze runs cooler with a grey undertone while honey bronze leans warmer and more amber. Side by side under kitchen lighting the difference is noticeable, even though photos often flatten it.
Can I mix pull finishes in one kitchen?
Yes, mixing two finishes works well when one is the primary cabinet finish and the other is reserved for an island or a single accent run. Mixing three or more finishes in one kitchen usually reads as unplanned.
How many pulls does a standard kitchen need?
A standard kitchen with 30-40 linear feet of cabinets typically needs 20 to 30 pulls between drawers and doors. Islands and appliance panels add to that count separately.
What's the standard cc spacing for kitchen island pulls?
Island pulls commonly run 6.5 inch to 9.75 inch center-to-center since island drawers and doors tend to be wider than standard base cabinets. The Du Verre Series 3 at 9.75 inch is built specifically for this use.
One Last Thing
The pull that gets returned most isn't the wrong finish, it's the right finish in the wrong cc spacing bought without checking the existing holes first. Measure before you fall in love with a photo — every pick on this list has its exact cc spacing listed for a reason.